Trans Chem Coatings Industrial FinishesTranschem Coatings

MSDS
Home Up Feedback Contents Specifications Links Search

Home

 

TRANS CHEM COATINGS

 


MATERIAL SAFETY DATA SHEET  

 

Section I

GENERAL INFORMATION

Manufacturers Name: Trans Chem Coatings             Date Prepared: 4/1/2000

Street Address: 1680 Miller Ave.. Los Angeles CA 90063

Emergency No.: 1- 800-421-2849                             Information: 213-747-7725

 

Product Class: Paint                                     V.O.C.: <2.2 Lbs/gal (262 g/l)

Product Name: Water Base Baking Enamel 2000


Section II

INGREDIENTS/ IDENTITY INFORMATION

Polyester Resin (Mix)

CAS# not established

NIOSH (RTECS) not established

OSHA PEL: not established

ACGIH TLV not established

Percent <45 %

___________________________

Water

CAS# 7732-18-5

NIOSH (RTECS) ZC0110000

OSHA PEL: not established

ACGIH TLV not established

Percent <35 %

_____________________________

Secondary Butanol

CAS# 78-92-2

NIOSH (RTECS) EO1750000

OSHA PEL: 100 ppm

ACGIH TLV 150 ppm

Percent <5%

______________________________

Ethylene Glycol Monobutyl Ether

CAS# 111-76-2

NIOSH (RTECS) KJ8575000

OSHA PEL: 50 ppm

ACGIH TLV 25 ppm

Percent <3%


Section III

PHYSICAL CHEMICAL CHARACTERISTICS

Physical Form : Liquid

Color : n/a

Odor : Slight

pH : >8.0

Boiling Point : Approx. 212 deg F

Melting/Freezing Point : Approx. 32 deg F

Solubility in Water : Complete

Specific Gravity : 1012

Bulk Density : 8.5 Lbs/gal

% Volatile by Weight : Approx. 68%

Vapor Pressure : n/k


Section IV

FIRE & EXPLOSION HAZARD DATA

Flash Point : 75 deg F (sec Butyl Alcohol)

Flammable Limits:

Upper Explosive Limit (UEL) (%) : 9.8% (sec Butyl Alcohol)

Lower Explosive Limit (LEL) (%) : 1.7% (sec Butyl Alcohol)

Auto-Ignition Temperature : no data

Extinguishing Media : Dry Chemical; Carbon Dioxide; Form; Water

Special Fire Fighting Procedures : Full emergency equipment with self-contained breathing apparatus and full protective clothing should be worn by firefighters. During a fire, irritating, highly toxic gases may be generated by thermal decomposition or combustion.

Unusual Fire / Explosion Hazards : Isolate from heat, electrical equipment, sparks and open flame. Closed container may explode when contaminated with water (CO2 evolved). Solvent vapors may be heavier than air.

Stagnant air may cause vapors to build up and travel along the ground to an ignition source which may result in a flash back to the source of the vapors.


Section V

REACTIVITY DATA

This product is stable.

Conditions to avoid: strong oxidizers

Incompatibility: Coagulation may occur following freezing, thawing or boiling.

Hazards polymerization: None


Section VI

HEALTH HAZARD DATA

Acute Hazard: Burning, tearing, drying or cracking of skin, coughing, chest pain, difficulty in breathing, nausea, vomiting, abdominal discomfort, diarrhea. Medical conditions generally aggravated by exposure-any respiratory or skin condition

Possible routes of entry: inhalation, ingestion, skin absorption

Emergency and first aid procedures: Eyes: Flush with water for 15 minutes. Skin: Wash with soap and water, not with solvents. Inhalation: Remove to fresh air from exposure area., give CPR if necessary. Ingestion: Do not induce vomiting. In all cases, obtain immediate medical attention.

Carcinogenicity:     NTP: No     IARC: No     OSHA: No

HMIS:         Health: 1             Flammability: 1             Reactivity: 0


Section VII

PRECAUTIONS FOR SAFE HANDLING AND USE

Precautions to be taken in handling storage:

Keep containers closed when not in use. Do not store above (115 deg. F ) keep from freezing. Empty containers may contain product residue. Do not cut, puncture or weld containers. All label warning must be observed, until container has been cleaned or reconditioned, or properly disposed of. Mix material well to proper specifications.

Spills: Wear air supplied NIOSH approved respirator for major unventilated release. Cover with absorbent material and keep loosely covered for 48 hours. Clean up residue with water.


Section VIII

CONTROL MEASURES

Ventilate area; remove spills with inert absorbent.

Waste disposal method: Dispose in chemical disposal area or in a manner that complies with local state and federal regulations, do not incinerate closed containers.

Use protective gloves, chemical splash safety glasses, and protective resistant apron.

DOT ID#: UN1263

DOT proper shipping name: n/a (Water Base Paint)

DOT Label: n/a (Non-Flammable Liquid)

DOT Class : n/a