TRANS CHEM COATINGS
MATERIAL SAFETY DATA SHEET
Manufacturers Name: Trans Chem Coatings Date Prepared: 4/1/2000
Street Address: 1680 Miller Ave. Los Angeles CA 90063
Emergency No.: 1- 800-421-2849 Information: 213-747-7725
Product Class: Paint V.O.C. : <3.2 Lbs/Gal
Product Name: Catalyst/ Epoxy Mil-P-23377G
Part 2 of 2
INGREDIENTS/ IDENTITY INFORMATION
Xylene (SARA III)
NIOSH (RTECS) ZE2100000
OSHA PEL: 100 ppm/ 150 STEL
ACGIH TLV 100 ppm/ 150 STEL
Methyl Ethyl Ketone
NIOSH (RTECS) EL6475000
OSHA PEL: 200 ppm
ACGIH TLV 200 ppm
ACGIH STEL 300 ppm
OSHA PEL: 50 ppm
ACGIH TLV n/k
PHYSICAL CHEMICAL CHARACTERISTICS
Physical Form : Liquid
Color : Clear, Pale Yellow
Odor : Of Solvent
pH : n/a
Boiling Point : Approx. 176 degF (Methyl Ethyl Ketone)
Melting/Freezing Point : Not established
Solubility in Water : Insoluble
Specific Gravity : Approx .754
Bulk Density : Approx. 6.3 lbs/gal
% Volatile by Weight : Approx. 51%
Vapor Pressure : 78 mm Hg/ 68F (Methyl Ethyl Ketone)
FIRE & EXPLOSION HAZARD DATA
Flash Point : 20 deg F (-7.0 C) Methyl Ethyl Ketone
Upper Explosive Limit (UEL) (%) : 11.4% (Methyl Ethyl Ketone)
Lower Explosive Limit (LEL) (%) : 1.8% (Methyl Ethyl Ketone)
Auto-Ignition Temperature : Not established
Extinguishing Media : Dry Chemical; Carbon Dioxide; Form; Water
Special Fire Fighting Procedures : Full emergency equipment with self-contained breathing apparatus and full protective clothing should be worn by firefighters. During a fire, irritating, highly toxic gases may be generated by thermal decomposition or combustion.
Unusual Fire / Explosion Hazards : Isolate from heat, electrical equipment, sparks and open flame. Closed container may explode when contaminated with water (CO2 evolved). Solvent vapors may be heavier than air. Stagnant air may cause vapors to build up and travel along the ground to an ignition source which may result in a flash back to the source of the vapors.
This product is stable
Conditions to avoid: moisture, excessive heat, sources of ignition
Incompatibility: avoid water, reactive materials
Hazards decomposition products: carbon dioxide/ carbon monoxide/ metal oxides
Hazards polymerization: None
HEALTH HAZARD DATA
Acute Hazard: Burning, tearing, drying or cracking of skin, coughing, chest pain, difficulty in breathing, nausea, vomiting, abdominal discomfort, diarrhea. Medical conditions generally aggravated by exposure-any respiratory or skin condition. Possible routes of entry: inhalation, ingestion, skin absorption
Emergency and first aid procedures: Eyes: Flush with water for 15 minutes. Skin: Wash with soap and water, not with solvents. Inhalation: Remove to fresh air from exposure area., give CPR if necessary. Ingestion: Do not induce vomiting. In all cases, obtain immediate medical attention.
Carcinogenicity: NTP: No IARC: No OSHA: No
PRECAUTIONS FOR SAFE HANDLING AND USE
Precautions to be taken in handling storage:
Keep containers closed when not in use. Do not store above (115 deg. F ) keep from freezing. Empty containers may contain product residue. Do not cut, puncture or weld containers. All label warning must be observed, until container has been cleaned or reconditioned, or properly disposed of. Mix material well to proper specifications.
Spills: Wear air supplied NIOSH approved respirator for major unventilated release. Cover with absorbent material and keep loosely covered for 48 hours. Clean up residue with solvent.
Ventilate area; remove spills with inert absorbent.
Waste disposal method: Dispose in chemical disposal area or in a manner that complies with local state and federal regulations, do not incinerate closed containers.
Use solvent resistant protective gloves, chemical splash safety glasses, and protective solvent resistant apron.
DOT ID#: UN1263
DOT proper shipping name: Paint or Paint Related Material
DOT Label: Flammable Liquid
DOT Class 3